Plastic Lumber Equipment and recycling and extrusion machinery

To find an item on this page hit CTRL+F

American Cierra Equipment's Newest Listings

7359	EREMA		Hydraulic			SCREEN CHANGER
Model:	SW 4/170 RTF	Size:	170mm	L/D Ratio:		Year:
EREMA Screen Changer SW 4/170 RTF, 170mm, Rexroth 3 KW hydraulic unit. OAD: 64" W. X 42" T. X 24"D.
7360	SML CONTI		Continuous			SCREEN CHANGER
Model:	90/1120/6	Size:	3.5"	L/D Ratio:		Year:	2009
SML CONTI 90/1120/6 Continuous Screen Changer, 3.5", *Never been used.
7362	SWECO		Screener/Shaker			SCREENER/SHAKER
Model:	US48	Size:	48"	L/D Ratio:		Year:
SWECO 48" Round Separators on stands. Self Cleaning Kit. Vibratory type screener, sifter, classifier for separating materials of different sizes.
7363	SWECO		Screener/Shaker			SCREENER/SHAKER
Model:	US24	Size:	24"	L/D Ratio:		Year:
SWECO Vibro-Energy Separator /Classifier/ Sifter, 24" diameter, Single Deck, 2" blank spacing frame, 8" scalping frame, 1/4 hp 1/60/460v 1140 rpm Baldor motor, includes top cover, appears in very good condition.
7361	SWECO		Screener/Shaker			SCREENER/SHAKER
Model:	S18S33	Size:	18"	L/D Ratio:		Year:
SWECO Separator / Classifier/ Sifter, Model S18S33, 18" dia, Triple deck, 115v, 1/4 hp motor. No screens with unit.
7364	Egan		Standard Single Screw			EXTRUDER
Model:		Size:	8"	L/D Ratio:	32	Year:	2009
Screw 8" diameter x 32:1 L/D, Reported less than 1 million lbs of use for polyester extrusion. Used on Eqan extruder.
7358	Johnson		Sheet			DIES
Model:		Size:	40"	L/D Ratio:		Year:
JOHNSON 40" Flex-Lip Film Die, Center fed, Vertical discharge. Last used on a 3 1/2" x 32:1 extruder.
7355	BERG		Air Cooled			CHILLER
Model:	BTU-7.5	Size:	7.5 Ton	L/D Ratio:		Year:
BERG Model BTU-7.5 Air Cooled Portable Chiller Module, 460v 3 phase, 60hz, 20 amp.
7356	Egan		Sheet			EXTRUSION/TAPE - FILM
Model:		Size:	52"	L/D Ratio:	32	Year:
EGAN 52" Tape / Slit Film Line, 1981 Hopper feed. Johnson Extruder with controls, 4.5" x 32:1, 200 hp 460v 3/60, 11.4:1 gearbox. Continuous screen changer. Polymer pump. 52" slit film die - reported improved design to provide stronger tape without fibrillator. 60" water cooled chill roll with air knife. H.E.A.T. SL-550 Oil Heater, 1999 yr, 575v, 550 deg F 100 psi, 86 kw. NO oven. 1st Godet - 3 rolls with nip, 12" dia x 52" face, 7.5 hp. 2nd Godet - 5 rolls with nip, 12" dia x 52" face, 50 hp. Control panel for chill roll & godets. MCC panel. We can supply an oven and takeup winders separately.
7354	HYDRECLAIM		Water Ring			PELLETIZING LINE
Model:	6 / 3.5" Dual Diameter	Size:	6/3.5"	L/D Ratio:	30	Year:	1884
HYDRECLAIM Pelletizing System 6 / 3.5" Dual Diameter, 30:1 L/D, 75 HP, 575v, 72 amp, manual screen changer, includes hopper, blowers, crammer feed, Beringer underwater pelletizer & spin dryer.
7350	Prodex		Standard Single Screw			EXTRUDER
Model:		Size:	4.5"	L/D Ratio:	24	Year:
PRODEX 4.5" Extruder, 24:1 L/D, 150 HP, Complete with controls.
7351	Davis Standard		Standard Single Screw			EXTRUDER
Model:	60 IN 80 R	Size:	6"	L/D Ratio:	30	Year:	1995
DAVIS STANDARD Extruders, 6" Diameter, 30:1 L/D, 1995 yr, Model 60 IN 80 R, 150 HP DC, 480v. (1) with drive. (1) missing barrel (?), screw, and drive.
7352	Davis Standard		Standard Single Screw			EXTRUDER
Model:	60 IN SPW24301	Size:	6"	L/D Ratio:	24	Year:	1983
DAVIS STANDARD Model 60 INONTHDSPW24301 Extruder, 24:1, 300 hp, Electrically heated water cooled (closed loop) barrel at approximately a 42" centerline height. Gearbox has a ratio of approximately 17:21 and is direct driven in a wrap-around manner by a 300 HP Reliance DC motor with SCR control. Gearbox is rated at 562 HP at a service factor of 1.5. On-center feed throat measures 8" x 12". C-clamp on discharge. Includes free standing temperature panel with Eurotherm 94 controllers and operator control panel. Manufactured 12/83.
7348	HARTIG		Standard Single Screw			EXTRUDER
Model:		Size:	4.5"	L/D Ratio:	30	Year:	1980
MIDLAND ROSS HARTIG 4.5" Extruder, 30:1 L/D, 150 HP, Reliance DC motor, 1725/2100 rpm, Lufkin gearbox 17.55:1.40, 1980 yr, S/N 4677.
7347	Davis Standard		Standard Single Screw			EXTRUDER
Model:		Size:	4.5"	L/D Ratio:	30	Year:	1989
2 Available Machine DAVIS STANDARD Extruders, 4.5" diameter, 30:1 L/D, 1989, Water Cooled, New DC motor, no controls.
7346	HOBBS		Extruder			LAB EQUIPMENT
Model:		Size:	1"	L/D Ratio:		Year:	1995
HOBBS 1" R&D Extruder, Hastolly barrel liner, 2 hp, 180v, 9.4 amps, Dynisco pressure measurement, Barber Colman AT580 temperature controllers, rebuilt 1995.
7349	Prodex		Standard Single Screw			EXTRUDER
Model:	450-8-24	Size:	4.5"	L/D Ratio:	24	Year:
PRODEX 4.5" Extruder, 24:1 L/D, Reliance 150 HP DC w/ MaxPak Drive, 500v 1750/2300 rpm, frame B3610ATZ, 244 amps. Has older style controls but reported working when stopped. Last used in compounding line.
7353	MAPEX		LowBoy Single Screw			EXTRUDER
Model:	150mm	Size:	6"	L/D Ratio:	32	Year:	95/7
MAPEX Extrusion Systems 150mm Extruders, 32:1 L/D, ~1995-97 yr, 6 zone heaters (each 3x400, 18000 watts, 250x750). (1) extruder with Kollman Gearbox 12.39:1, Type PEZS 48/120 AP, 12 cooling fans. (1) extruder with Fritz Phillips Gearbox type EX560 gearbox, 262 KW, 12.30:1 ratio, 10 cooling fans. Both appear in good condition, NO motors or controls, last reported use in ~ 2005 to recycle PP fiber waste.
7345	Barmag		Single Screw			COMPOUNDING LINE
Model:	4	Size:	2"	L/D Ratio:	24	Year:	2000
COLOR COMPOUNDING PELLETIZER LINE, ~2000 yr. Description Ktron Hurricane Filterless Vacuum Hopper Unit; McGuire Products Weigh Scale Blender; McGuire feed Hopper, 1 compartment, vertical motor blending,; McGuire feed Hopper, 4 compartments; Barmag 15 hp extruder with horizontal screw; Berlyn pellet machine, model 4; and Berlyn pellet cutter, 4" slot. 2" extruder with L over D 24:1
7344	BRABENDER		Extruder			LAB EQUIPMENT
Model:	EX-250	Size:	3/4"	L/D Ratio:	25	Year:
BRABENDER EX-250 PLASTICORDEREXTRUDER BRABENDER INSTRUMENTS MODEL EX-250 APPROXIMATELY .75" DIAMETER 25:1 L/D RATIO (3) ZONE ELECTRICALLY HEATED BARREL EXTRUDER. 2.75" DIAMETER FEED CONE. 23.5" LONG SCREW WITH DIE. 0-200 RPM GAUGE. GE MODEL TYPE PL-V300 3HP 230 VOLT 100 VOLT 1.03 AMP FIELD 1 VOLT 15.3 AMP ARM. 2500 RPM TYPE GP-100 DC DYNOMETER MOTOR DRIVE (S/N 246/65). 0-200 RPM GAUGE. 1/60/220 VOLT 25 AMP CONTROL. S/N 740-66. INCLUDES THERMOTRON TEMPERATURE CONTROL UNIT. OAD: 40" WIDE X 56" LONG X 35" HIGH. 580# WEIGHT. More Photos available. PRICE: $10,500.00 Location - PA.
7343	Killion		Rolls			LAB EQUIPMENT
Model:		Size:	8"	L/D Ratio:		Year:	1983
Killion 8" , 3 Roll Chrome Stack complete with Pull Rolls and Controls. All in Excellent Condition. More photos available.
7340	Luwa		n/a			MELT PUMP
Model:	XTREX 9090	Size:	6"	L/D Ratio:		Year:
EXOOTH_0003 30 HP Luwa Melt Pump 30 HP Luwa Melt pump Model XTREX 9090, S/N 817637/4. 3,000lbs/Hr. Discharge pressure 3,000psi. Last used on 6" PTI extruder
7339	Welex		n/a			MELT PUMP
Model:	70-70	Size:	6"	L/D Ratio:		Year:
Welex pump 70-70 Part# 11000024 Ser# 87-22 Luwa / Extrex 10.7 Cubic inches per revolution 30 HP Dc Motor * The Gear box is rated up to 40HP. Just removed from 6" sheet line, it's in excellent running condition.
7342	Polytruder Extruder		Standard Single Screw			EXTRUDER
Model:	3.0 - 24 - 75	Size:	3"	L/D Ratio:	24	Year:	2001
3" Polytruder Extruder, 24:1 L/D, 75 HP, Model 3.0 - 24 - 75. Serial No. 210424, Built 2001, 75 hp inverter duty motor, 230/460 voltage, Flender gear reducer. Feed hopper with magnet. 5 barrel zones, 2 die zones, digital readouts. Digital RPM, AMP, and Melt Pressure readout. Unitized control panel, overall 10' L x 54" W x 9' High.
7335	Bonnot		Soap Bar			EXTRUDER
Model:	Stainless Steel 12 Duplex	Size:	12	L/D Ratio:		Year:	80's
BONNOT Stainless Steel No. 12 Duplex. 12" Vacuum Plodders. 25HP w/AC Variable Speed Drive. Originally for making Soap Bars. Unit is now disassembled as seen in photos.
7334	Product Engineered Systems		Air Classification System			AIR CLASSIFICATION SYSTEM
Model:	72-40	Size:	72" x 40"	L/D Ratio:		Year:	2010
PES- Micro Rotary Screener All Stainless Steel Construction, 48,000 CFM, 25HP 208-230/460V Heavy Duty Shaft Mount Gear Motor, Air Knife for Continuous Screen Cleaning, Steam Spray Nozzle Header for frequent cleanups, Heavy Duty High Temperature Seals.
7333	HARTIG		Standard Single Screw			EXTRUDER
Model:		Size:	3.5"	L/D Ratio:	30	Year:
3.5 Hartig Extruder, 30:1 L/D, Electrically Heated, Water Cooled, Control Cabinet missing temp controls, 75 HP DC Motor & Drive, Die Clamp, comes with 2 Screws. * Unit was removed from service last running Sheet Profile. Temp. Controllers were remover wile in storage.
7236	Prodex		Strand			PELLETIZING LINE
Model:		Size:	6"	L/D Ratio:	32	Year:
6" Prodex Extruder, 32:1 L/D, Vented, Complete Temp Control Panel w/250HP DC Drive, Screen Changer, Strand Die, Water Bath and 14" Cumberland Pelletizer. Missing 250HP Motor.
7330	MAAG		n/a			MELT PUMP
Model:	PS70/70	Size:	3.5"	L/D Ratio:		Year:	99
Maag melt pump Model PS70/70 20 hp DC Motor & Drive Prints dated 9/20/99 Cad.file ps70-3002
7332	After Market		Batch			DENSIFIER
Model:		Size:		L/D Ratio:		Year:	2004
Four Units Available. All are missing their Controls, 250HP Motors and Blades. Very Simular to MGB-Engineering. About the only thing different are the Doors. $15,000 for all 4 Densifers !!!
7322	Werner Pfleiderer		Twin Screw			EXTRUDER
Model:	ZSK-170	Size:	170 mm	L/D Ratio:	24	Year:	1991
Werner Pfleiderer 170 mm Twin Screw Extruder 1991, Machine No. ZSK-170. Co-rotating design, 24:1 L/D, 6 barrel sections, Electrical heating, water cooled, 2000 H.P Drive Motor (NA), Includes control panels. Pictures available. Complete rebuild in 2003. The gearbox is: Type RWP 146, 1774 kw rating, 1770 input, 326 output speed. W&P Polyrex Type PR-12-4 Gear Pump, 1991, Machine No. SWZ-1900, 400 hp drive. 3.48:1 Ratio Gearbox. W&P Screen pack changer, Model SWZ 700, 1991, 700 sq.CM filter area.
7328	Procedyne		Fluid Bed Oven			MISCELLANEOUS
Model:	30-9-15	Size:	30"L x 9"W x 15"D	L/D Ratio:		Year:
Procedyne Fluid bed oven. Chamber is 30" Long 9" Wide and 15" Deep. There is a small quantity of fluid bed sand to go with the unit it's in the fiber drum seen the the photo.
7320	Magna Max DVR		Diesel			GENERATOR
Model:	432RSL4009	Size:	KVA 234 / Amps649	L/D Ratio:		Year:
· Magna Max DVR · Model 432RSL4009 · Serial LM-238635-0501 · Type RSL · Kw 187 / volts 120/208Y · KVA 234 / Amps649 · Mounted on skid rack with a new penman 8V71 Detroit Motor. * Generator sits in the back of a box truck.
7321	Tow Behind		Nat. Gas			GENERATOR
Model:		Size:	Kw 10.0 / stand by Kw 12.5	L/D Ratio:		Year:
Tow behind generator · 120volt / 60 cycle · Continuous Kw 10.0 / stand by Kw 12.5 · Continuous amps 10.0 / stand by 12.5 - N/gas
						PAPER WINDER
Model:		Size:		L/D Ratio:		Year:

7316	Berlyn		Lab Pelletizing Line			LAB PELLETIZING LINE
Model:		Size:	1"	L/D Ratio:	30	Year:
1" Berlyn Extruder, 30/1 Vented, Strand Die, 7 HP DC Motor with Controls , Water Bath, Air Wipe and a Berlyn Pelletizer .
7317	Egan		Standard Single Screw			EXTRUDER
Model:		Size:	3.5	L/D Ratio:	24	Year:	1986
3.5" EGAN Extruder, 24:1 L/D, Electrically Heated Air Cooled, 125 HP DC Motor & Drive, Complete Temperature Control Panel with Digital Controls and Die Clamp.
7319	Mitts & Merrill/Cumberland		Shredder/Granulator Combo			SHREDDER
Model:	5028M&M/50BCumberland	Size:	50" x 28" / 20" x50"	L/D Ratio:		Year:
Complete Shredding & Grinding operation. All conveyers and electricals are included in the offer. Mitts & Merrill Shredder (Model) 5028 - 28" x 50") 120hp, 230/460V, 3 PHz. Cumberland Model 50H, 200 HP Motor with a Low Voltage Starter, Solid Rotor, Stargered Blades, Blower Discharge with Cyclone. May be inspected while operating . Price: Fob. Location
7314	SSI		Dual Shaft			SHREDDER
Model:		Size:	60" x 40"	L/D Ratio:		Year:
SHREDDING SYSTEMS, INC. (SSI) Shredder, 40" x 60" Opening, 200 hp, Hopper with Hydraulic Ram. Reported as in "Excellent Shape". Can be used for tires, plastics, TV’s and light metals.
7313	EMERY		Up Cut			SAW
Model:	PS-4	Size:		L/D Ratio:		Year:
Emery Traveling up-cut saw. 2 HP 230/260V, 14" Blade, pneumatically operated Up-Down-Forward-Back. Safety Guard. Come with Manual. Excellent for cutting pipe and other profiles
7315	WEIMA		Single Shaft			SHREDDER
Model:	WLK-13	Size:	52" x 47"	L/D Ratio:		Year:
WEIMA Model WLK-13 Shredder, Single Shaft Completely refurbished. 15" Diameter Rotor "New" 68 Cutters 52" x 47" Hopper Opening 75 HP Motor 10 HP Hydraulic Ram
7312	RETECH VECOPLAN		Single Shaft			SHREDDER
Model:	RG62/125U	Size:	62 x	L/D Ratio:		Year:	2006
RETECH VECOPLAN Shredder, Model is RG62/125U, Started up in late 2006 and has 2475 hrs. The Retech is equipped with 74 blades and is currently being used in a plastics operation, the shredder can be used for wood, plastics, document destruction and paper baler preparation.
7311	Nelmor		Shredder/Granulator Combo			SHREDDER
Model:	SH2525	Size:	25" x 25"	L/D Ratio:		Year:	1997
Dual Shaft Shredder 25 x 25 chamber opening. Huge conveyor feed hopper. 20 HP drive on shredder. Material drops from shredder into a Nelmor G16295P1 granulator. powered by a 50 HP motor .The shredder will chop the material into 2" shards and the grinder will reduce it to about 3/8 of an inch chips. Feed opening on grinder is 16 x 29.5". It has a three blade rotor . with Blower evacuation system with Imcs and a 700 LB capacity surge bin. this is fed by a 24" wide by 15' long feeding conveyor.
7310	Ball & Jewell		Shredder/Granulator Combo			SHREDDER
Model:	SB-10-515/SG-2026-S	Size:	19" x 25"	L/D Ratio:		Year:
BALL & JEWELL Shredder Model SB/10-515 "Shred Buster" The shredder, 19" x 25" shredding chamber, comes w/ a 10 hp motor. Includes a Model SG-2026-S granulator. 20" x 26" grinding chamber, 3 knife scissor cut, open rotor, flywheel and 40hp motor. Also includes 5" Loadamatic/Blowamatic discharge powered by 3 hp motor. The system concludes with a B&J inclined feeding conveyor, 19" width. Set up to run 480v, 3 phase. It was shredding plastic lumber. The granulator is on rails which allow it to be moved in or out under the shredder. Yellow access stand comes with it.
7308	Covel		SUFFACE			GRINDER
Model:		Size:		L/D Ratio:		Year:
Covel Surface Grinder with caramax magnetic chuck..............$2,500
7307	Quincy		ROTORY SCREW			Air Compressor
Model:	350	Size:		L/D Ratio:		Year:
Two compressors available. Quincy Rotary Screw, Model 350, 75hp, excellent condition. Removed running meticulously maintained. These are computer controlled, AIR COOLED, ready to run. $7,000 ea.
7309	SHRED TECH		Dual Shaft			SHREDDER
Model:	ST-75ES	Size:	37" x 46"	L/D Ratio:		Year:
SHRED TECH: Two 40 HP Motors Electrical: 460v 3 Phase, 50/60hz. Feed Hopper Opening: 37 ?"x 46". Cutting chamber: 37 5/8" x 25". Weight: 7,600 lbs. Floor Space: 42.9 Sq. ft. Manufacture Date: 2001 (has been in storage several years). Low hours - Excellent Condition New $120,000.00 Used primarily for shredding a high volume of paper documents.
7303	Berstorff		Twin Screw			EXTRUDER
Model:		Size:		L/D Ratio:	40	Year:	1984
40mm BERSTORF Twin Screw Extruder, 40:1 L/D, 460-RPM Screw Speed, Control Panel, 575V System. * 3 ports in barrel other than feed port, also side feed port
7302	Maris		Twin Screw			EXTRUDER
Model:		Size:	65mm	L/D Ratio:	32	Year:
65mm MARIS Twin Screw Extruder, 32:1 L/D, 300-RPM Screw Speed, Control Panel, 150HP DC Motor & Drive, 230/460V, 12 Hole Strand Die. * Come w/spare screws and Segments. Last used to manufacture Color Concentrates.
7301	Baker Perkins		Twin Screw			EXTRUDER
Model:	Co-Rotating	Size:	80mm	L/D Ratio:	12	Year:
Barker Perkins Twin Screw Co-rotating, 60 HP, w/Spare set of Shafts and Segments. Comes with 12 Hole Strand Die.
7326	NRM		Mono-extrusion			SHEET LINE
Model:	Pacemaker III	Size:	4.5"	L/D Ratio:	24	Year:
NRM Pacemaker 4.5" extruder, 150 HP, screen changer, 52" flexlip die, water cooled Welex 3 roll stand 18" X 53" Wysong Shear 1452 Rubber pull roll with spare rolls Spare chrome and matte rolls Spare flex lip die 45"
7300	Pappenmier		Batch			MIXER / BLENDER
Model:	500L 50/100	Size:	500 Liter	L/D Ratio:		Year:
Pappenmier 500 Liter Mixer w/Electricals Bolw is in very good condition
7298	NRM		Mono-extrusion			SHEET LINE
Model:	Pacemaker III	Size:	4.5"	L/D Ratio:	24	Year:
NRM Pacemaker 4.5" extruder, 150 HP, screen changer, 52" flexlip die, water cooled Welex 3 roll stand 18" X 53" Wysong Shear 1452 Rubber pull roll with spare rolls Spare chrome and matte rolls Spare flex lip die 45"
7293	Nelmor		Closed Rotor			GRANULATOR
Model:	2036	Size:	20"x 36"	L/D Ratio:		Year:
20"x 36" ,150 hp nelmore grinder, solid rotor, 6 blades staggered, 480 volt 3 phase with blower and cyclone.
7299	DEC		Air Classifier			DUST COLLECTER
Model:	UMA25K5AD	Size:	24" W x 36" L x 72" T	L/D Ratio:		Year:	1995
DCE~ Dust Control Equipment 3hp, 480 volt,
7294	Conair		Open Rotor			GRANULATOR
Model:	SK-1420	Size:	14" x 20"	L/D Ratio:		Year:
Conair 14"x 20", 3 knife open rotor, 50 hp, 480 volts comes with blower, cyclone and surge bin.
			Air Classification System			AIR CLASSIFICATION SYSTEM
Model:		Size:		L/D Ratio:		Year:
3hp, 480 volt, DCE dust control equipment
7338	Conair		Open Rotor			GRANULATOR
Model:	SK-286701	Size:	14" x 18"	L/D Ratio:		Year:
Conair 14"x 18", 3 knife open rotor, 30 hp, 480 volts comes with blower, cyclone.
7336	Conair		Open Rotor			GRANULATOR
Model:	SK-286701	Size:	14" x 18"	L/D Ratio:		Year:
Conair 14"x 18", 3 knife open rotor, 20 hp, 480 volts comes with blower, cyclone.
7290	Davis Standard		Standard Single Screw			EXTRUDER
Model:	N/A	Size:	3.5"	L/D Ratio:	34	Year:
DS 3 1/2" Extruder Liquid cooled 100 hp motor & Drive 34/1 L/D ratio With heat control cabinet
7288	Cumberland		Open Rotor			GRANULATOR
Model:		Size:	30" x 18"	L/D Ratio:		Year:
Cumberland Granulator 30" X 18" Chamber Open Rotor Twin Shear slicing action 75 HP, 230/460V Comes with a 3/8" and 1/4" Screen Blower * ( Belt housing enclosure is slid open for photo ) needs paint job.

Return To Top Of This Form

Home

American Cierra Equipment, Inc.
144 Genesee Street
Suite 102-207
Auburn, New York 13021
Phone: 315.252.5668
sierraric@aol.com